1. This Board Rocks has been moved to a new domain: CarolinaPanthersForum.com

    All member accounts remain the same.

    Most of the content is here, as well. Except that the Preps Forum has been split off to its own board at: http://www.prepsforum.com

    Welcome to the new Carolina Panthers Forum!

    Dismiss Notice

Ripping doors

Discussion in 'Home Improvement & DIY Forum' started by chipshot, Nov 29, 2006.

Page 3 of 5
  1. Nov 29, 2006 at 2:09 PM #21
    chipshot

    chipshot Full Access Member

    Age:
    50
    Posts:
    33,519
    Likes Received:
    0
    Joined:
    Feb 6, 2002
    Location:
    Boise
    you all can eat fucking large pry bar
     
  2. Nov 29, 2006 at 2:10 PM #22
    HollyB

    HollyB Iz Lives

    Age:
    45
    Posts:
    18,080
    Likes Received:
    1
    Joined:
    Apr 21, 2005
    :rotflmao:

    who you gonna hire to feed it to us?
     
  3. Nov 29, 2006 at 2:12 PM #23
    JeykleHyde

    JeykleHyde MPD Test Subject

    Posts:
    1,018
    Likes Received:
    0
    Joined:
    Dec 17, 2005
    Location:
    In the recesses of her mind

    :tongue3:
     
  4. Nov 29, 2006 at 2:13 PM #24
    chipshot

    chipshot Full Access Member

    Age:
    50
    Posts:
    33,519
    Likes Received:
    0
    Joined:
    Feb 6, 2002
    Location:
    Boise
    a cheap Biltmore whore
     
  5. Nov 29, 2006 at 2:14 PM #25
    mathmajors

    mathmajors Roll Wave

    Age:
    55
    Posts:
    42,103
    Likes Received:
    0
    Joined:
    Jan 8, 2003
    Fred'll do it free for you.
     
  6. Nov 29, 2006 at 3:31 PM #26
    builder

    builder membered member

    Age:
    53
    Posts:
    56,687
    Likes Received:
    1
    Joined:
    Jan 7, 2003
    Location:
    wonderful world of oz
    and make sure you leave room for sanding off the splintered edges that you didn't tape first.
     
  7. Nov 29, 2006 at 3:37 PM #27
    chipshot

    chipshot Full Access Member

    Age:
    50
    Posts:
    33,519
    Likes Received:
    0
    Joined:
    Feb 6, 2002
    Location:
    Boise
    Do you cut up to the tape or through the middle?
     
  8. Nov 29, 2006 at 3:56 PM #28
    builder

    builder membered member

    Age:
    53
    Posts:
    56,687
    Likes Received:
    1
    Joined:
    Jan 7, 2003
    Location:
    wonderful world of oz
    Luan? If they aren't solid wood, you need to put masking tape on the line you're cutting and cut down the center of it. The tape will create surface tension and keep splintering to a minimum.
     
  9. Nov 29, 2006 at 3:58 PM #29
    chipshot

    chipshot Full Access Member

    Age:
    50
    Posts:
    33,519
    Likes Received:
    0
    Joined:
    Feb 6, 2002
    Location:
    Boise
    they aren't solid wood, no

    I was aware of the tape trick, just never done it
     
  10. Nov 29, 2006 at 4:03 PM #30
    chipshot

    chipshot Full Access Member

    Age:
    50
    Posts:
    33,519
    Likes Received:
    0
    Joined:
    Feb 6, 2002
    Location:
    Boise
    I saw that
     
Page 3 of 5

Share This Page